Log in
Log in

or
Create an account

or
Learning
1 comment

Have Fun with Noise Gates

Noise Gates Don't Have to be Boring

Noise gates aren't as relevant as they were back in the analog days, when hiss was an uninvited intruder on anything you recorded. But noise gates can do some really cool special effects that have nothing to do with reducing hiss. This article shows how to make them a lot more interesting, and throws in a bunch of fun audio examples, too. But first, let's do some noise gate basics for the uninitiated.

Noise Gates Basics

 

A noise gate mutes its output with low-level input signals, but higher-level signals can pass through. Following are the typical adjustable parameters found in a noise gate, whether analog, digital, or plug-in.

  • Threshold: If the input level to the gate passes below the threshold, the gate “closes” and mutes the output. Once the signal exceeds the threshold, the gate opens again.
  • Attack: This determines how long it takes for the gate to go from full off to full on once the input exceeds the threshold.
  • Decay: This sets the time required for the gate to go from full on to full off once the signal falls below the threshold. Since decaying signals often criss-cross the threshold as they decay, increasing the decay time prevents “chattering.”
  • Key input: Normally, the gate opens and closes based on the input signal’s amplitude. The key input allows patching in a different control signal for the gating action (for example, using a kick drum as the key signal to turn a sound on and off in time with the kick’s rhythm). Note that in most cases, you won’t find this in plug-ins, only in hardware units.

All right, let’s get into applications.

 

Selective Reverb

 

I was using a premixed drum loop from the Discrete Drums Series 2 library, but in one particular part of the song, I wished that the snare—and only the snare—had some reverb. Although Series 2 is a multitrack library, I didn’t want to go back and build up the drum loop from scratch. So why not just extract the snare drum sound, put some reverb on that, and mix it in with the drums?

 

Referring to Fig. 1, I copied the drum loop in Track 1 to a second track in my sequencer (if you were doing this in hardware, you’d split it into two mixer channel inputs). In the second track, there’s EQ inserted to roll off all the low end, which took most of the kick out of the signal, as well as the high end, to reduce the level of cymbal crashes.

 

 

Reverb sélective
Fig.1

The next step was to insert a noise gate in Track 2, and raise the gate threshold so that only the snare peaks made it through (the screen shot shows a Compressor/Gate plug-in, but the compressor was disabled by setting the ratio to 1:1). These peaks fed the reverb, which dumped into the master bus along with the original drums. The end result: Reverb on the snare only, added in with the rest of the drums.

 

Here is an example of selective reverb below. The first four measures are the loop only, the next four measures are the extracted/reverbed sound only, and the last four measures combine the two. See? It is possible!

 

 

00:0000:00

 

Pseudo-Peak Expander

 

A similar trick works for situations where a drum part is not dynamic enough. Split the signal to an additional mixer channel, and set its gate so that only the peaks come through. Adjust this module’s level so that the peaks add to the original sound, thus providing a boost only on peaks. This also works with any kind of percussive transient—pick noise on guitar, for example, or percussive B3-type transients.

Grotesque Distortion

 

Setting the attack and decay time to the minimum amount possible (typically 0 ms with attack, and anywhere from 0 to 10 ms with decay) can cause the gate to open and close so fast that it actually triggers on individual cycles of the input signal, causing distortion.

 

This technique works especially well with highly compressed drums; in this context, the threshold now becomes an “ugly” control. At low thresholds, you’ll hear an occasional buzz. Higher thresholds can give mean, nasty, spiky sounds. (Note: if there is a minimum decay time, this will set a limit on the highest frequencies that will be affected. For example, with 5 ms of decay, anything above about 200 Hz will not be affected on a per-cycle basis.)

 

Check out a defenseless drum loop being distorted by this technique:

 

00:0000:00

 

Attack Delay Unit

 

Adding some attack time in the 100–250 ms range allows a signal to “swell” to its maximum level. For instance, if you pause briefly between notes, when a new note exceeds the threshold it will fade in over the specified amount of attack time. This can alter the attack characteristics of percussive instruments like piano and guitar, or add “brass-like” attacks to organ sounds. Another interesting use is with vocals, to reduce breath inhale noises. As the singer breathes in, the inhale fades in. This makes the breath sound less prominent, but doesn’t cut it out completely (which can sound unnatural).

 

However, for this application the decay time setting is also important. With a long decay, the gate may remain open during the space between notes, which prevents triggering a new attack when a new note plays. Conversely, too short a decay can result in the “chattering” effect described earlier. So, use the shortest possible decay time, consistent with a smooth sound.

 

Kick Drum “Hum Drum”

 

Here’s a trick for hardware noise gates. Suppose you want to augment an existing kick drum sound with a monster rap kick, like that famous TR-808 rap sound. Here’s a sneaky way to do it:

  1. Set a sine wave test tone oscillator somewhere between 40 and 60Hz, and plug it into a mixer channel module containing the noise gate.
  2. Patch the kick drum into the gate’s key input and set the threshold relatively high, so that the kick exceeds the threshold for only a very short amount of time.
  3. Set the noise gate decay for the desired amount of oscillator decay. Hopefully your gate decay can go up to about 2 seconds, but even 1 second can do the job.

Now whenever the kick drum hits, it opens up the gate for a fraction of a second and lets through the sine wave; the decay time then provides the desired fadeout.

Real Time Manipulation

 

This real-time performance tip can sound very cool with hip-hop, techno, and other types of music that rely on variations within drum loops. With most loops, the snare and kick will reach the highest levels, with (typically) hi-hat below that and percussion (maracas, shakers, tambourine, etc.) mixed in the background. Tweaking the noise gate threshold in real time causes selected parts of the loop to drop out. For example, with the threshold at minimum, you hear the entire loop. Move the threshold up, and the percussion disappears. Move it up further, and the high-hat drops out. Raise it even higher, and the snare and kick lose their decays and become ultra-percussive.

 

Listen to an audio example with a loop being processed by a noise gate in real time:

 

 

00:0000:00

 

For this application, you want no attack time and a fairly short decay (about 50 ms). This can add really cool dynamics to a drum loop.

 

So who says noise gates have to be boring? Check out some of these techniques, and you’ll have a whole different take on the little critters.

 


Originally published on Harmony Central.  Reprinted with permission.

 

  • mapsnmad 1 post
    mapsnmad
    New AFfiliate
    Posted on 03/04/2011 at 20:46:02

    Another great example of Craig Anderton's tips. I clicked on the link because the topic looked interesting, and then I found the article was by Craig. No wonder it was so interesting. You are like a DIY MacGyver music ace.

Would you like to comment this article?

Log in
Become a member