Tusq nuts classified ad
New ad alertImages
Reviews
4.7/5(3 reviews)
67 %
33 %
Write a user review
Maurice GentilGreat
Published on 10/12/13 at 09:19 (This content has been automatically translated from French)Nut graphite modeled for Telecaster and Stratocaster. This nut is fully prefabricated replace Nut Telecaster. I personally have a problem with a badly adjusted saddle that stifled the E string acute. I replaced the old nut for it. No adjustment necessary, the sound becomes clearer, fuller, great.
70
»
Joe-Rhysa nut for good sound!
Published on 06/11/12 at 06:43 (This content has been automatically translated from French)I bought 2 weeks ago.
I have not bought other brands, I took what I found in milonga ...
I think it's a good saddle for acoustic guitar, I think it balances out the strings at the sound reproduction that sustain and hard, hard and my guitar seems more warm in his notes ...
here's a change from the horrible plastic nut that supported my acoustic WS ...
I think it's a good investment for a first prize sound; just 7 euros for enhanced sound ...
with experience .... I change my acoustic guitar for a better model! ah! ah!
I have not bought other brands, I took what I found in milonga ...
I think it's a good saddle for acoustic guitar, I think it balances out the strings at the sound reproduction that sustain and hard, hard and my guitar seems more warm in his notes ...
here's a change from the horrible plastic nut that supported my acoustic WS ...
I think it's a good investment for a first prize sound; just 7 euros for enhanced sound ...
with experience .... I change my acoustic guitar for a better model! ah! ah!
20
»
kinnePublished on 06/05/08 at 06:11 (This content has been automatically translated from French)
I made a series of reversible changes to my Fender American Standard Stratocaster because despite the passage in two makers, the problems (buzz) persisted.
I changed the Nut, the guide ropes and bridges.
This opinion concerns the Nut "Graph Tech Nut" graphite with pre-cut notches, not the room white Tusq shown above.
Replacement Nut was an operation which I found very difficult. We had to remove the original part and then scratch the surface of my maple neck using a sharp knife and use a screwdriver to lift the nut end. Fortunately, everything went well with no damage.
The play Graph Tech has a pin that I had to file because there is no corresponding hole on the sleeve of my...…
I changed the Nut, the guide ropes and bridges.
This opinion concerns the Nut "Graph Tech Nut" graphite with pre-cut notches, not the room white Tusq shown above.
Replacement Nut was an operation which I found very difficult. We had to remove the original part and then scratch the surface of my maple neck using a sharp knife and use a screwdriver to lift the nut end. Fortunately, everything went well with no damage.
The play Graph Tech has a pin that I had to file because there is no corresponding hole on the sleeve of my...…
Read more
I made a series of reversible changes to my Fender American Standard Stratocaster because despite the passage in two makers, the problems (buzz) persisted.
I changed the Nut, the guide ropes and bridges.
This opinion concerns the Nut "Graph Tech Nut" graphite with pre-cut notches, not the room white Tusq shown above.
Replacement Nut was an operation which I found very difficult. We had to remove the original part and then scratch the surface of my maple neck using a sharp knife and use a screwdriver to lift the nut end. Fortunately, everything went well with no damage.
The play Graph Tech has a pin that I had to file because there is no corresponding hole on the sleeve of my Start. The curvature of the saddle is not exactly the handle and I had a little sand to reduce the width. Then I could fix the saddle again by adding a drop of glue in the middle. Nothing insurmountable, but work fine anyway.
I use a set of string slightly thicker than the grooves of the nut, ideally, should therefore expand a little nicks, but I have no problem and most importantly, this change in addition to replacing the original bridges will be removed the buzz.
The guitar is finally set properly, without noise and is more enjoyable to play.
It is a good modification to do with caution, however, and we must find the right piece for the handle because there are many models from Graph Tech. The one I bought was probably not ideal for gutiare.
I changed the Nut, the guide ropes and bridges.
This opinion concerns the Nut "Graph Tech Nut" graphite with pre-cut notches, not the room white Tusq shown above.
Replacement Nut was an operation which I found very difficult. We had to remove the original part and then scratch the surface of my maple neck using a sharp knife and use a screwdriver to lift the nut end. Fortunately, everything went well with no damage.
The play Graph Tech has a pin that I had to file because there is no corresponding hole on the sleeve of my Start. The curvature of the saddle is not exactly the handle and I had a little sand to reduce the width. Then I could fix the saddle again by adding a drop of glue in the middle. Nothing insurmountable, but work fine anyway.
I use a set of string slightly thicker than the grooves of the nut, ideally, should therefore expand a little nicks, but I have no problem and most importantly, this change in addition to replacing the original bridges will be removed the buzz.
The guitar is finally set properly, without noise and is more enjoyable to play.
It is a good modification to do with caution, however, and we must find the right piece for the handle because there are many models from Graph Tech. The one I bought was probably not ideal for gutiare.
See less
40
»
Tech. sheet
- Manufacturer: Graph Tech
- Model: Tusq nuts
- Category: Other Guitar Replacement Parts
- Added in our database on: 08/25/2006
We have no technical specifications for this product
but your help will be much welcomed
»
Other categories in Guitar Replacement Parts
Other names: tusq nuts, tusqnuts