Log in
EN
FR

Marshall 4x12 Guitar Cabinets

45 products found

Filter
Sort by
Evaluation
  • Reviewed or not
  • Editor’s award
  • Reviewed by Audiofanzine
Availability
  • Available or not
  • Sold new or used
  • Sold new
  • Sold used
Must-have products
  • All products
  • Flagship products
  • Best rated products
  • Hot products
  • Popular products
Price
  • Freeware
  • Low-cost (< $800)
  • Mid-range ($800 - $950)
  • Premium (> $950)
€
Clear
Sort by
  • Popularity
  • User ratings
  • Price - low to high
  • Price - high to low
  • Used price, increasing
  • Used price, decreasing
  • Name (from A to Z)
  • Name (from Z to A)
  • Added on
Sort results
  • Popularity
  • User ratings
  • Price - low to high
  • Price - high to low
  • Used price, increasing
  • Used price, decreasing
  • Name (from A to Z)
  • Name (from Z to A)
  • Added on

The best Marshall 4x12 Guitar Cabinets reviews

The reviews Audiofanzine members found the most helpful.
  • « Good Cabs on the Used Market »

    Features: 4 Celestion G12T-75s @ 300w mono/150w stereo (each side) 4 & 16 ohm mono ouputs 8 ohm stereo ouputs Birch ply construction MDF back panel The construction of this cab leaves something to be desired. While it's built of quality materials (besides the back panel, which is made out of MDF), Marshall definitely cuts corners on these cabs. I've played quite a few new (and used) ones, and all of them suffered from the same downfalls. The screws around and inside the entire cab aren't screwed in tightly, leading to unwanted vibrations at higher volumes. The openings aren't properly sealed and release air. The MDF back panel is better replaced with a birch panel. The speakers are clipped on, instead of soldered, with thin wiring. The baffle board support beam is screwed in off-center. These problems can be fixed by: - Securely screwing in all screws (especially on the baffle board) - Replacing the back panel with birch - Caulking around the baffle board, handle inserts and jack plate for a tight seal - Screwing in the baffle board beam in the center - Soldering the wires to the jacks, using heavier gauge wire With all these mods, you should have a very nice sounding, high quality cabinet that sounds great and only takes a few minutes to do the mods. As far as the sound goes, the stock G12T-75s aren't for everyone. I find they mix well with Marshall amps, and other mid-gain to low-gain amps, as they have a scooped mid range that balances out an amp with a prevalent mid spike (like Marshalls), and also work great for a cleaner sounding amp, where scooping the mids a bit will produce a nice, chimey, clean tone. However, I don't find they work well with most modern voiced, high gain amps, as they produce too much of a scoop in the mids, and leave the amp's tone hallow and sterile. Pickiness aside, these cabs sound great, especially for the price you can get them for on the used market. While I wouldn't suggest these for everyone, if you can find one at a cheap price, and don't mind putting in a little work to get it in tip-top shape, they're certainly hard to beat!

  • « Your typical 4x12 »

    Love them or hate them, the Marshall JCM900 1960 cabinet is probably the standard 4x12 cabinet out there on the market. No matter what music shop you walk into, you’re bound to find one of these somewhere on the showroom floor. Equipped with four Celestion G12T75 speakers, the cabinet is able to withstand 300 watts of power. The selectable ohmage and stereo switching on the back makes it a fairly versatile cabinet, and it should be adequate for most gigging musicians out there. The cabinet is made out of birch plywood, but the back panel is actually made out of MDF. Some people like the MDF back, and some people don’t. Contrary to popular belief, the MDF backing has actually been around for quite some time, so it’s not something new that Marshall has been doing. The wiring is pretty skimpy and should be replaced, in my opinion. The tolex is alright, but it can ding somewhat easily. Grill cloth and piping are fine, but some people prefer the salt and pepper grill cloth for tone. Yes, different grill cloth can result in different tones as it determines how much dampening occurs between the speaker and your ears. The biggest complaint I have with this cabinet is that it tends to leak some air. This means that it’s not as tight and focused as it could be. Taking the time to use some caulking around the seams can help improve the cabinet’s overall sound. The handles are plastic and tend to break when thrown around a bit. Thankfully, Scumback Speakers makes 100% drop-in replacements to fix this issue. The other handles on the market actually don’t line up 100%, so keep that in mind when ordering cheaper metal handles. The G12T75s are probably some of the most notorious speakers on the market. Quite a few people dislike them, and I’m one of those people. They tend to sound very scooped and harsh, even in this rear loaded cabinet. Mixed, they can sound pretty good, but alone, they’re just not for me. If you’re looking for a 4x12, this cabinet should definitely be on your list. However, if you’re willing to spend a bit more, there are better cabinets on the market.

  • Audiofanzine FR's review

    (Originally written by elco7/translated from Audiofanzine FR) - Two inputs for stereo amplifier heads. - Four 75-watt 12" Celestion speakers - 4/8/16-ohm selector for stereo or mono operation, or to setup an additional cabinet like the 1960A . - Rewired with 2.5mm cables! It's so good... - Small gauge Proco cable and Fender Platinum instrument cable - Engl Thunder and/or Mesa Single Rectifier amp heads. The front panel is slightly slanted to the top so that the sound doesn't stay on the ground. Good imaging. This speaker cabinet reproduces all attacks and nuances of your playing, as well as all amp setting variations. Don't stay in front of the GT12T speakers because they are very loud. Their measurement diagram shows it clearly. The cabinet is very good and provides much better vibrations than the slanted 1960A. Slanted cabinets don't look so nice and their design is an aberration for the internal vibrations. Slanted cabinets should have chambers, not the 1960A. The 1960B can produce heavy lows that stay on the ground. Mids and highs have a higher dispersion. Thus it sounds aggressive, full and dynamic, but V30 speakers would provide better results (because of the high-frequency boost of the GT12T speakers). I find the sound less sharp for recording applications, but that depends on many parameters. I wouldn't buy it again because it's not the time for me to have two cabinets! The value for money is great for a secondhand model. But with a bit more money you can buy another cabinet with V30 or G12M Greenback speakers.