Become a member
Become a member
Continuer avec Google

or
Log in
Log in
Se connecter avec Google

or
learning

Sidechain

How Does a Sidechain Work?

Back in the analog area, audio effects with a sidechain circuit were rare and usually among the most expensive. So sidechain was used only in big productions to fine tune the processing of certain recordings. With modern DAWs, sidechains are now available to everyone and most dynamic processors include them. Nowadays, people use the sidechain to create sound effects that are very common in electronic music.

If you take a look at the audio gear market, you'll notice that those units featuring a sidechain are dynamic processors (compressors, limiters, gates, expanders) and a few exotic effects, like dynamic EQs. In fact, all these processors have something in common: their behavior depends directly on the signal.

Standard dynamic processors use a threshold level to trigger the processing: in a compressor/limiter, the gain is reduced when the input signal level exceeds the threshold; likewise, in a gate/expander, the gain is reduced when the input level drops below the threshold. So the audio source is both the trigger and the object of the processing.

The idea of the sidechain was born from the need to control better the way the processor reacts to the level of the source signal. So, a second circuit was added. The signal in this circuitry is called the "trigger" and it only controls the behavior of the processor. By nature, this signal is not audible in the audio output of the processor. But how can you feed the sidechain and process the trigger signal?

Source signal + filter

The first type of sidechain includes a low-cut filter (or sometimes a low-shelf filter see EQs) and uses the source signal as the trigger signal.

Sidechain

You'll find this type of sidechain in many compressors because it allows you to reduce the pumping effect when a full-range signal is heavily compressed (see Compressors). Let us explain that better: in an audio signal, most of the energy is concentrated in the low-end. Since the compressor is triggered by the signal level, it is more responsive to low frequencies than to high frequencies. As a consequence, each bass-drum hit triggers the compressor, which results in the attack not being processed while the rest of the signal is damped due to the gain reduction applied. By attenuating the low-frequency range of the trigger signal with the sidechain's low-cut filter, we decrease the impact of low frequencies in the triggering of the compressor and thus reduce the pumping effect.

In the past, pumping was considered an unwanted effect, but nowadays it is intentionally used in many music genres.

Source signal + insert

The second sidechain type also uses the source signal as the trigger, but replaces the low-cut filter with an insert.

This kind of sidechain can be found in some hardware compressors. The insert (see Insert vs Aux) allows you to process the sidechain signal with an EQ instead of the low-cut filter.

External signal

Sidechain

The last type of sidechain allows you to trigger the processor with any external audio signal. But ─ you'll say ─ the insert return in the sidechain described above also allows us to feed the detection stage with an external signal! Which is true; this third sidechain type is not really that different.

But why should I use an external trigger signal? The most common application consists in feeding the sidechain of a noise gate with a rhythm signal, in most cases the hi-hat or a percussion instrument, which you can process with an EQ, if necessary. What happens in this case is that the gate closes between the beats in the trigger signal and cuts the source signal regularly. The result is a sort of signal-segmentation effect heard on vocals and lead instruments in many modern productions.

A practical detail

All these features are very nice but how can we control what happens in the sidechain if the trigger signal is not audible? On hardware compressors equipped with a basic sidechain (source signal + low cut), you might have no possibility to monitor the trigger signal, which doesn't really matter. But generally, sidechain circuits provide features that allow us to switch to an external signal (key input or sidechain input) and to monitor the trigger signal (key listen or sidechain listen).

  • captinvidio 1 post
    captinvidio
    New AFfiliate
    Posted on 06/29/2013 at 00:37:45
    31 band graphic in the side-chain and or ring modulator can produce sum inst-ring FX (remember flower power 1969) in conventional music.and electronic music much fun to be had with the side-chain [the ring modulator can suppress the fundamental leaving only the harmonics to be processed]
    the graphic enables fine control of the harmonics in the in the control side-chain and control d roll off of base
    KEEP THE TUBES A GLOWING AND THE MUSIC FLOWING.
    kind regards Stephen Muir-Field retired PYE technical department

Vous souhaitez réagir à cet article ?

Log in
Become a member
cookies

We are using cookies!

Yes, Audiofanzine is using cookies. Since the last thing that we want is disturbing your diet with too much fat or too much sugar, you'll be glad to learn that we made them ourselves with fresh, organic and fair ingredients, and with a perfect nutritional balance. What this means is that the data we store in them is used to enhance your use of our website as well as improve your user experience on our pages (learn more). To configure your cookie preferences, click here.

We did not wait for a law to make us respect our members and visitors' privacy. The cookies that we use are only meant to improve your experience on our website.

Our cookies

Cookies not subject to consent

These are cookies that guarantee the proper functioning of Audiofanzine and allow its optimization. The website cannot function properly without these cookies.

Website preferences

We store your preferences so that you do not have to re-enter them every time your come back (forums options, dark or light theme, classifieds filter, standard or buzz news, newsletters popups...).

Log in

This one makes sure you don't have to re-enter your credentials every time you visit Audiofanzine.

Analytics

This data allows us to understand the use that our visitors make of our website in an attempt to improve it.

Advertising

This information allows us to show you personalized advertisements thanks to which Audiofanzine is financed. By unchecking this box you will still have advertisements but they may be less interesting :)

We did not wait for a law to make us respect our members and visitors' privacy. The cookies that we use are only meant to improve your experience on our website.

Our cookies

Cookies not subject to consent

These are cookies that guarantee the proper functioning of Audiofanzine and allow its optimization. The website cannot function properly without these cookies.

Website preferences

We store your preferences so that you do not have to re-enter them every time your come back (forums options, dark or light theme, classifieds filter, standard or buzz news, newsletters popups...).

Log in

This one makes sure you don't have to re-enter your credentials every time you visit Audiofanzine.

Analytics

This data allows us to understand the use that our visitors make of our website in an attempt to improve it.

Advertising

This information allows us to show you personalized advertisements thanks to which Audiofanzine is financed. By unchecking this box you will still have advertisements but they may be less interesting :)


You can find more details on data protection in our privacy policy.